Color steel tile broken body shell using 25mm - 30mm manganese steel production, thickening shaft, thickening knife plate, fixed knife using manganese steel and special tool steel two kinds, with wear resistance, impact resistance, toughness function, general manganese steel material can be broken more than 300 tons of waste light metal. Special tool steel can break 1500 tons, both materials can be repaired. Caigang tile crusher manufacturers with hydraulic device can be ready for maintenance of the machine,. This machine design is reasonable, the outward appearance is generous, may according to the user need to change the system to enter the material the size, does not return the material, will not cause the personnel injury.
Color Steel Tile Crusher can crush waste Color Steel Tile, can, paint bucket, etc., metal materials are crushed into small metal particles in the crushing chamber, providing high quality raw materials for smelting steel and iron, realizing the recycling of resources, color steel tile crusher, energy saving and environmental protection good helper, make a fortune good partner. The waste iron and steel raw materials are transported to the feed inclined surface by the scale plate conveyor, and the feed inclined surface is equipped with two high and low grinding rollers that can be rotated to flatten it and send it into the crusher. In the crusher, ten disks fixed on the main shaft and ten hammer heads installed between the disks can swing freely to support, through the kinetic energy generated by high-speed rotation, scrap steel is broken, torn and broken, scrap steel is processed into blocks or groups, through the lower and upper grids, fall on the vibrating conveyor. If the first batch fails to be processed into scrap steel small enough, it will be processed again in the crusher by the rotating disc and hammer head until it can pass through the grid. If you accidentally enter the crusher, the operator should open the discharging door under the top in time and pop them out. In the crusher crushing at the same time, the crusher on the water in order to cool down and avoid dust.
Metal Crusher is mainly used to realize the decomposition and crushing of large mouth waste metal, and to realize the fine crushing of waste metal, so as to achieve a better benefit prospect in the transportation cost and recovery price of waste metal. This series of equipment is a kind of multi-purpose and high efficiency metal kneading ball equipment produced by our factory. it can be used to achieve good paint removal effect and granulation effect whether it is used in end-of-life cars or waste cans. In the working principle of the equipment, the metal pulverizer makes use of the basic principle of the hammer strike, under the drive of the high speed and high torque motor, the hammer head on the rotor of the main engine takes turns hitting the material to be broken into the cavity, through the space formed between the liner plate and the hammer head, Tear the debris to be broken into pieces in accordance with the specifications. According to the working condition of the crusher, it can be divided into dry system, wet system and semi-wet system. Dry system mainly means that the broken material must pass through the air rotary sorting system to separate the metal and non-metal, in addition, the whole system is equipped with dust removal device. Wet system is to spray water at the same time of crushing, and to wash with water at the same time of sorting. The semi-wet system only carries out a small amount of water spraying when the crushing needs, to prevent dust, and there is no cleaning. As a high quality equipment for scrap metal crushing treatment, metal crusher can greatly improve the disassembly efficiency of waste metal in terms of investment value, and at the same time enhance the purity of waste iron and steel to provide high quality burden for low cost smelting of scrap metallurgy industry.
Metal crusher series products mainly include: easy to pull can grinding, color steel tile crushing, scrap car crushing, paint barrel crushing, iron chip crushing and other series of products can be used for a variety of waste metal recycling crushing processing.
In the working flow, the metal pressing block is fed into the forced feeding and crushing port of the equipment through the feeding device, and the metal pressing block is primary broken by the crushing process of the pressing roller and the coarse crushing shaft, The metal pressing material after primary crushing enters the main engine cavity of the equipment, and under the drive of a high speed and high torque motor, the hammer head on the rotor of the main engine takes turns hitting the metal pressing material entering the main engine cavity through the space between the lining plate and the hammer head, When the crushing block can be fully and effectively broken in the crushing chamber, the crushing block can be torn into a fragment in accordance with the specifications, and then flow down from the screen. The broken material is separated by an air rotary sorting system, and the paint, rust and waste plastic in the metal press block are separated, and the material unloaded at the bottom of the equipment is then transported to the aggregate point through the conveying equipment, In this process, the non-magnetic materials contained in the materials are separated and unloaded from the production line to the non-magnetic materials pile under the action of the magnetic separator.
In addition, the whole system is equipped with dust removal device to minimize the harm of dust pollution in the production process. The equipment mainly has the advantages of high output, low energy consumption, high efficiency, uniform discharge and so on. When the equipment is used, the noise is low, there is no pollution, the operation is simple and the maintenance is convenient.
(1) selection of equipment type.
(2) Design and manufacture products according to the special requirements of customers.
(3) training of technical personnel for clients.
(4) The company plans the site for the user free of charge, designs the suitable process and the plan.
(1) acceptance of the product.
(2) assisting clients in the preparation of construction plans.
(1) assign special after-sales service personnel free of charge to guide customers to install and debug.
(2) installation and debugging of equipment.
(3) on-site training of operators.
(4) after the installation of the complete set of equipment, the full-time technical personnel may assist the customer in on-site production until the user is satisfied.
Looking for ideal Mobile Crusher Plant
Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Hot Sale Mobile Impact Crusher are quality guaranteed. We are China Origin Factory of Heavy Crusher Plant. If you have any question, please feel free to contact us.
Product Categories : Crusher Machine > Color Steel Tile Crusher